DR-D207 Battery Burning Test Chamber
A purpose-built burner, specimen screen and removable octagonal mesh cover for controlled flame-exposure testing of approved lithium cells or small batteries. Specify the adopted method, specimen and laboratory safety plan before treating any fixture geometry as a compliance claim.
What the Test Helps You Observe
During a specified flame-exposure procedure, a cell or approved small battery sits above the burner while the screen and octagonal surround define the setup and help retain ejected material. The laboratory observes the behavior required by its adopted method; pass/fail criteria must come from that method and the test plan, not from the chamber specification alone.
Controlled setup
Published burner, screen, opening and octagonal-cover dimensions provide a starting point for method review.
Visible evidence
Agree in advance how the operator will record exposure time, specimen behavior and any ejected material.
Safer procurement
Confirm fuel supply, exhaust, operator protection and post-test handling before ordering.
Published DR-D207 Configuration
| عنصر | Published value | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
|---|---|---|
| Control and timer | Button control; flame-time setting shown as 0–99H99M | Confirm actual timer input format, resolution and shutoff behavior. |
| Burner and opening | Bunsen burner, 10 mm internal mouth, approximately 100 mm length; test opening 100 ± 2 mm | Confirm burner type, flame setting and fixture drawing against the adopted standard edition. |
| Specimen screen | 0.43 mm stainless woven wire; 20 openings per inch | Confirm mounting height and replacement screen supplied. |
| Octagonal cover | 610 mm across opposite faces; 305 mm high; eight removable panels; 0.25 mm aluminum wire, 16–18 openings per inch | Request dimensional drawing and panel-retention details. |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | 750 × 750 × 500 mm internal; 1000 × 950 × 1310 mm external, including door lock | Confirm usable clearance around the fixture and doorway. |
| المرافق | Methane or LPG supplied by customer; 220 V, 50/60 Hz, 200 W; approximately 160 kg | Confirm gas regulation, ventilation, site power and nameplate. |
| Relief and exhaust | 200 × 200 mm pressure-relief door; rear Ø100 mm exhaust connection; door-retention chain | Confirm discharge direction, duct requirements and risk-assessed containment limits. |
Method Fit: Review the Clause, Not a Logo List
The DR-D207 screen and octagonal-surround geometry warrants review against the UL 1642 Projectile Test, but published fixture similarity is not proof of conformance. In particular, the DR-D207 page specifies a Bunsen burner, while a published technical comparison describes a Meker-type burner for the UL 1642 fire-exposure setup. Verify the adopted edition, burner, all dimensions, specimen preparation, observation and acceptance rules clause by clause before any UL 1642 claim.
Do not treat this chamber as a UN 38.3 test method. The UN transport manual has defined T.1–T.8 tests; a generic “UN 38.3 T.10 burning test” claim should not appear on this page. Other standards such as UL 2054 or IEC 62133-2 may form part of a laboratory program but do not automatically validate this fixture.
Send the exact method
Standard edition, clause, cell format, sample state, exposure period and pass/fail rule.
Confirm the physical setup
Burner specification, mesh, opening, screen-to-burner position and octagonal-cover drawing.
Confirm evidence
Video/observation plan, timed exposure, calibration records and final report format.
DR-D207 Is Different from DERUI's Other Battery Fire Equipment
| Equipment | Primary function | Do not assume |
|---|---|---|
| DR-D207 burning test chamber | Burner, screen and octagonal mesh fixture for specified cell/small-battery flame exposure | Large pack fire testing, programmable heating or certified blast containment |
| DR-D211 EV battery cell fire tester | A different external-flame test setup; compare its published specimen and burner limits separately | Interchangeability with the DR-D207 projectile-test geometry |
| Battery thermal abuse chamber | Controlled high-temperature exposure in a heated enclosure | An open-flame burner or octagonal-mesh projectile-test fixture |
Site Safety and Acceptance Plan
Review the specimen
Provide chemistry, dimensions, maximum energy, charge state and credible venting behavior. Agree allowable specimen size and quantity.
Review the facility
Confirm methane/LPG supply, regulator, exhaust route, clearance, fire response and operator exclusion area with site EHS.
Witness the setup
Check burner, screen and cover dimensions, timer, gas shutoff behavior, exhaust, door and documentation during FAT.
Questions Buyers Ask
Is this a UL-certified chamber?
No certification evidence is established by the public product page. Review fixture suitability against the exact UL 1642 edition and obtain any required third-party evaluation separately.
Can it test EV modules or packs?
Do not infer that from the enclosure size. Obtain a specimen-size, energy and hazard assessment, then compare the appropriate larger-scale equipment.
Is the gas included?
The published specification says methane or LPG is customer-provided. Confirm regulator, hose, shutoff and local installation scope in the quotation.
Does it perform UN 38.3 transport testing?
No. This burner arrangement should not be presented as a UN 38.3 test. Choose the dedicated equipment for the required T.1–T.8 method.
What needs confirmation before publication or purchase?
The adopted standard edition, fixture drawing, timer format, safety controls, real-device photos, accessories and measurable FAT criteria.
Request a Method-Matched DR-D207 Proposal
Send your cell drawing and test clause. DERUI can respond with the fixture drawing, included scope, utility list and an acceptance checklist that engineering and purchasing can review together.
Include in the inquiry
- Standard edition and exact clause
- Cell/battery format and energy
- Gas and exhaust conditions
- Required observation and FAT records
