Piso 1, No. 3, Avenida Shugang, Vila Hongmei, Cidade de Dongguan, Província de Guangdong, China
Configure environmental and safety test equipment for EV and lithium-ion cells, modules and packs. Select temperature, humidity, low-pressure and abuse-test systems from the exact method and hazard assessment.
Battery environmental and abuse equipment must be selected from battery chemistry, format, energy, state of charge, operating condition, expected failure modes and the exact procedure. No single chamber is suitable for every battery test.
Identify whether the requirement is environmental conditioning, altitude, thermal cycling, crush, impact, short circuit, vibration or fire exposure. Document expected gases, pressure, electrolyte release, fire and electrical hazards before selecting equipment.
Define the Battery Test Method →Temperature and humidity chambers produce controlled climatic profiles. Crush, impact, fire and electrical-abuse procedures require dedicated mechanisms and protection selected for the expected failure mode.
Compare Environmental and Abuse Tests →State whether the procedure requires climatic cycling, low-pressure exposure, or simultaneous temperature-pressure control. A battery altitude chamber and an altitude temperature chamber are different procurement decisions.
Review Battery Altitude Simulation →Provide dimensions, mass, quantity, stored energy, state of charge, energized heat load and required voltage, current, temperature, pressure or gas channels. Confirm cable ports and monitoring connections in the approved configuration.
Request an Interface Review →Select reinforced construction, pressure relief, exhaust, gas monitoring, fire-system interfaces, isolation and emergency shutdown from the battery risk assessment. Do not assume every feature is standard on every model.
Review Battery Abuse Equipment →Confirm electrical supply, room ventilation, exhaust destination, drainage, safety distances, emergency response and post-test handling. Define alarm, interlock, monitoring and record checks for factory or site acceptance.
Request a Site and Safety Review →Send the exact procedure and revision, battery chemistry, cell/module/pack format, dimensions, mass, quantity, stored energy, state of charge, operating connections, expected failure modes, monitoring channels and site-safety provisions.
Request a Battery Test Safety Review Download Battery Test Equipment InformationBattery test equipment selection
A battery temperature profile, a forced short circuit, a crush event and a fire exposure call for different equipment and laboratory safeguards. Start with the exact procedure, cell or module format, state of charge, stored energy and credible failure mode. Use the routes below to find the relevant product page; no single cabinet performs every battery test.
| Required test | Relevant product pages | What determines the configuration |
|---|---|---|
| Temperature exposure, climatic cycling or separated specimen levels | Câmara de Teste de Temperatura de Bateria Teste de Baterias de Lítio de Múltiplas Camadas da Derui |
Loaded temperature profile, specimen spacing, powered heat output, monitoring channels and safety requirements. Confirm any independent layer control in the approved configuration. |
| Reduced-pressure exposure | Battery Altitude Simulation Test Chamber | Specify absolute pressure, hold time, ambient-temperature conditions and specimen state. A low-pressure-only chamber is not automatically a combined temperature–pressure system. |
| Electrical abuse or cell cycling and measurement | Forced Internal Short Circuit Tester Sistema de Teste de Células de Bateria de Energia |
Define the exact short-circuit method, force and electrical records for the first system. The cell-testing system is a cycling/measurement platform, not a protective abuse chamber. |
| Impact, accelerated impact or crush | Câmara de Teste de Impacto em Bateria Battery Module Accelerated Impact Tester Câmara de Teste de Compressão de Bateria |
Impact energy or acceleration, contact geometry, specimen orientation, fixture, crush force and stop criteria are method-specific. These mechanisms are not interchangeable. |
| High-temperature abuse, flame exposure or fire observation | Battery Thermal Abuse Test Chamber Testador de Fogo de Células de Bateria de Veículos Elétricos Câmara de Teste de Queima de Bateria |
Programmed heating and direct flame are different exposures. Define the method, fuel or heat input where applicable, expected vent gas, exhaust route, isolation and emergency response. |
| Controlled vibration | Electromagnetic Vibration Test Bench | Specify sine, random or transport profile; frequency, acceleration, axes, duration, specimen mass, fixture and required control/report evidence. |
These details let engineering review the test mechanism, monitoring, safeguards and site interfaces together.
Send your battery test requirements to DERUI for an equipment and safety review →
A Derui Testing Equipment está sempre comprometida em fornecer soluções de tecnologia de teste precisas e fiáveis para a modernização industrial global, dedicada ao design e fabricação de equipamentos de teste de alta qualidade, como equipamentos de teste de papel e embalagem. Os nossos principais produtos incluem câmara de teste ambiental e câmara de teste climática
