ชั้น 1, หมายเลข 3, ถนนชูการ์, เมืองหงเหมย, ตงกวน, มณฑลกวางตุ้ง, ประเทศจีน

ผู้ผลิตห้องทดสอบสิ่งแวดล้อม 20 ปีส่งมอบลูกค้าทั่วโลกกว่า 3000 ราย           อีเมล: shirley@deruitest.com
WhatsApp Consultation:+86 135 2795 8363

ห้องทดสอบอุณหภูมิและความชื้นแบบป้องกันการระเบิดขนาดใหญ่ 3000 ลิตร

Product overview

The DR-H201-F3000 is a custom 3,000 L climate-chamber project for large test loads. Define the specimen, environmental duty, external test systems and facility protection interfaces as one coordinated equipment scope.

รายการ สเปค
Model / nominal volume DR-H201-F3000 / 3,000 L
Temperature configuration −70°C to +150°C
Humidity configuration 10% to 98% RH within the agreed operating envelope
Heating / cooling capability Up to 5 / 3°C/min; span, load and site conditions must be agreed
Project basis Custom drawing, utilities, interfaces and protection package
ปลอดภัยและเชื่อถือได้
คุณภาพดี
การรับประกันคุณภาพ
การปรับแต่ง
ข้อความWhatsApp
หมายเลขสายด่วน 15580327593
  • รายละเอียดสินค้า
  • คำถามที่พบบ่อย
  • คำถามที่พบบ่อย
  • ติดต่อเรา

DR-H201-F3000

ห้องทดสอบอุณหภูมิและความชื้นแบบป้องกันการระเบิดขนาดใหญ่ 3000 ลิตร

The DR-H201-F3000 is a custom 3,000 L climate-chamber project for large test loads. Define the specimen, environmental duty, external test systems and facility protection interfaces as one coordinated equipment scope.

DR-H201-F3000

Designed Around Large Loads, Not an Empty Chamber

Battery modules and packs

Provide specimen envelope, mass, state of charge, maximum electrical energy and powered heat so airflow and refrigeration capacity can be sized correctly.

Multiple specimens or fixtures

Define rack layout, clearances, cable routing and loading method. A nominal 3,000 L volume does not equal 3,000 L of usable specimen space.

Integrated test systems

Specify cycler connections, voltage and temperature channels, gas sampling, video, exhaust and data interfaces before the chamber layout is released.

DR-H201-F3000

DR-H201-F3000 Configuration

รายการ สเปค Project confirmation
Model / nominal volume DR-H201-F3000 / 3,000 L Confirm usable internal dimensions and door opening on the approved drawing.
ช่วงอุณหภูมิ -70°C ถึง +150°C Confirm required option, load, setpoint span and stabilization criteria.
ความเสมอภาคของอุณหภูมิ ±2°C Confirm whether this means deviation or uniformity, sensor map and loaded/no-load condition.
ช่วงความชื้น 10% ถึง 98% RH Request the combined temperature-humidity operating envelope; full RH range is not available at every temperature.
Heating / cooling rate up to 5°C/min / 3°C/min Define average or linear rate, start/end points, specimen load and cooling-water condition.
แหล่งจ่ายไฟ 220 V or 380 V, 50/60 Hz; customized Freeze voltage, phase, frequency, connected load and protective device.
Internal / external material Stainless-steel interior / reinforced coated-steel exterior Confirm grade, thickness, floor loading and corrosion requirements.
External dimensions Customized for installation Confirm transport route, doorway, service clearance and maintenance access.

DR-H201-F3000

Freeze the Non-Standard Design Inputs First

Define the climate duty

List temperature and RH setpoints, transitions, dwell times, cycles, tolerances and recovery requirements.

Define the real load

Provide dimensions, mass, quantity, fixtures, packaging, powered heat, cable loss and expected failure modes.

Define the facility interface

Confirm electrical supply, cooling water, drain, exhaust route, fire-system interface, room ambient and installation access.

DR-H201-F3000

Safety Functions Must Follow the Hazard Analysis

Function Information required before selection Acceptance evidence
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits Credible pressure event, relief direction, safe discharge area and facility clearance Approved calculation/drawing and functional inspection
Gas, smoke or flame detection Target hazard, sensor type/range, alarm thresholds and calibration Calibration record and cause-and-effect test
Forced exhaust Required airflow, duct material, discharge point, make-up air and purge time Measured airflow and interlock demonstration
Fire suppression Agent, design concentration, activation logic, drainage and local-code approval Approved system documents and functional test
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits Specimen power, chamber shutdown sequence, emergency stop and fail-safe state Interlock matrix and witnessed shutdown test
Reinforced enclosure Defined event, structural design basis, door/window/port construction Drawing review and agreed project-specific verification
Safety wording: “explosion-proof” is not a universal guarantee of battery thermal-runaway containment. The quotation must identify the exact functions supplied and the event they are designed to address.

DR-H201-F3000

DR-H201-F3000 Product View

Custom 3000L battery temperature and humidity test chamber with battery pack fixture

Product view. Internal layout, ports and protection functions follow the approved project drawing.

DR-H201-F3000

Standards and Certification Need Separate Decisions

Reference How it may relate What must be verified
IEC 60068-2-1 / IEC 60068-2-2 Cold and dry-heat environmental tests Applicable procedure, severity, load and chamber performance.
IEC 60068-2-78 Cab: steady-state damp heat Temperature-RH point, duration, specimen state and acceptance criteria.
UN 38.3 Lithium battery transport-test programme Only the applicable procedure should be mapped; the chamber does not perform every T.1–T.8 test.
UL 1642 / UL 2580 or customer specification Method-specific cell or EV battery safety evaluation Exact edition, clause, fixtures, monitoring and separate abuse equipment.
ATEX / IECEx / IEC 60079 Equipment for potentially explosive atmospheres Do not claim certification without the exact certificate, model/configuration scope, equipment marking and issuing body.

DR-H201-F3000

Recommended FAT for a Custom 3,000 L Chamber

Climate performance

Verify agreed temperature/RH points, empty and representative-load mapping, ramp definition, recovery and door-opening behaviour.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Check programme execution, alarms, access permissions, sensor records, export format, communication and power-failure recovery.

Safety cause and effect

Simulate every detector and fault input to verify alarms, isolation, exhaust, suppression command and safe-state sequence.

FAT limitation: a functional interlock test is not the same as proving containment of an uncontrolled battery event. Any destructive or certification test requires a separately agreed protocol and facility.

DR-H201-F3000

Information Required for an Accurate Quotation

Topic Send DERUI
Specimen Dimensions, mass, quantity, chemistry, capacity, SOC, electrical energy and packaging.
Test profile Temperature/RH programme, rates, dwell, cycles, tolerance and specimen operating mode.
Powered load Maximum watts, charge/discharge current, duty cycle and cable/feedthrough requirements.
Failure scenario Credible gas, smoke, flame, pressure, electrolyte, fragment and heat-release conditions.
Facility Power, cooling water, drainage, exhaust route, fire system, ambient and installation access.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits Mapping points, loaded performance, alarms, interlocks, data format and documentation.

DR-H201-F3000

Compare the proposed equipment against the real test

Purchasing decision

A large battery chamber quotation should identify the boundary between the chamber supplier, external cycler supplier and facility contractor. Compare the same specimen energy, powered heat, climate profile and installation assumptions. Items such as ductwork, cooling services, lifting, cable supports and emergency interfaces should have an assigned owner so they do not become unresolved work after delivery.

Application planning

For a battery module or pack connected to an external cycler, show the loading method, support arrangement, power-cable route and measurement connections. Identify heat released inside the chamber and any external equipment that affects the room. The nominal 3,000 L volume does not establish door clearance, floor capacity or a safe loading path for a particular pack.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Request a coordinated layout, utility schedule, interface list and safety cause-and-effect matrix before design approval. Agree the representative-load climate test and the functional interlock demonstration separately. If ATEX, IECEx or other certification is required, request the exact certificate and configuration scope; do not infer certification or thermal-runaway containment from the product designation.

DR-H201-F3000

Choose the equipment for the intended application

Request a DR-H201-F3000 configuration review

Send the specimen drawing, quantity, mass, operating profile, powered heat, interfaces and destination utilities. Include the acceptance criteria and required test records so the proposed configuration can be reviewed against the actual test.

Discuss My Test Requirements

ตรวจสอบ DERUI company information และ qualification documents. Confirm which supplied documents and configuration details apply to the equipment in your quotation.

เฟซบุ๊กLinkedInXRedditWhatsApp

พารามิเตอร์ทางเทคนิค

รายการ สเปค Project confirmation
Model / nominal volume DR-H201-F3000 / 3,000 L Confirm usable internal dimensions and door opening on the approved drawing.
ช่วงอุณหภูมิ -70°C ถึง +150°C Confirm required option, load, setpoint span and stabilization criteria.
ความเสมอภาคของอุณหภูมิ ±2°C Confirm whether this means deviation or uniformity, sensor map and loaded/no-load condition.
ช่วงความชื้น 10% ถึง 98% RH Request the combined temperature-humidity operating envelope; full RH range is not available at every temperature.
Heating / cooling rate up to 5°C/min / 3°C/min Define average or linear rate, start/end points, specimen load and cooling-water condition.
แหล่งจ่ายไฟ 220 V or 380 V, 50/60 Hz; customized Freeze voltage, phase, frequency, connected load and protective device.
Internal / external material Stainless-steel interior / reinforced coated-steel exterior Confirm grade, thickness, floor loading and corrosion requirements.
External dimensions Customized for installation Confirm transport route, doorway, service clearance and maintenance access.

Questions before ordering

Is DR-H201-F3000 a standard catalogue chamber?

No. It is a non-standard 3,000 L project. Dimensions, refrigeration, humidification, ports, utilities and safety controls must be confirmed against the test load and site.

Is 10% to 98% RH available throughout -70°C to +150°C?

No such full-envelope capability is established. Request the combined temperature-RH chart and define the required operating points.

Is the ramp rate guaranteed with a battery pack installed?

Not without a defined load. Rate type, span, payload mass, powered heat and facility conditions must be written into the technical agreement.

Does “explosion-proof” guarantee containment of thermal runaway?

No. A specific hazard scenario, engineered protection package, acceptance protocol and supporting evidence are required.

Is this model confirmed ATEX or IECEx certified?

Request the exact certificate, equipment marking and scope covering the proposed model and configuration. Certification should be confirmed from those documents before procurement.

What should be approved before production?

Approve the chamber drawing, usable workspace, climate duty, load, interfaces, utilities, safety matrix, FAT criteria, documentation and delivery scope.

How should we compare quotations for this configuration?

A large battery chamber quotation should identify the boundary between the chamber supplier, external cycler supplier and facility contractor. Compare the same specimen energy, powered heat, climate profile and installation assumptions. Items such as ductwork, cooling services, lifting, cable supports and emergency interfaces should have an assigned owner so they do not become unresolved work after delivery.

What evidence should be reviewed before approving the order?

Request a coordinated layout, utility schedule, interface list and safety cause-and-effect matrix before design approval. Agree the representative-load climate test and the functional interlock demonstration separately. If ATEX, IECEx or other certification is required, request the exact certificate and configuration scope; do not infer certification or thermal-runaway containment from the product designation.

WhatsAppWhatsApp
WhatsAppWhatsApp
WhatsApp
ข้อความข้อความ

ขอใบเสนอราคา