ชั้น 1, หมายเลข 3, ถนนชูการ์, เมืองหงเหมย, ตงกวน, มณฑลกวางตุ้ง, ประเทศจีน
Sand and dust environmental chambers engineered to test component seal integrity in compliance with IEC 60529 and ISO 20653.
Select a dust chamber from the required ingress rating, enclosure category, dust specification, circulation or airflow condition, vacuum requirement, specimen size and powered operating state.
Clarify whether the enclosure must be dust-protected or dust-tight and what constitutes a pass under the applicable procedure. The required rating determines severity, inspection and acceptance criteria.
Compare IP5X and IP6X Requirements →Determine whether vacuum-assisted testing applies to the enclosure category. Provide the specimen’s internal volume, extraction connection, pressure measurement and required extraction rate or limit.
Review Dust Ingress Equipment →Specify talcum powder or another method-defined dust, particle requirements, concentration and conditioning. Blowing sand and dust tests may also require controlled air velocity, temperature and exposure sequence.
Configure Sand and Dust Exposure →Provide the loaded envelope, number of specimens, supports and airflow clearance. Large enclosures can obstruct circulation and require greater chamber volume, dust recovery and cleaning access.
Size the Dust Test Workspace →State whether the specimen operates during exposure and list power, signal, pressure and temperature connections. Feedthroughs must support monitoring while maintaining chamber containment and safe operation.
Plan Powered Dust Testing →Define dust concentration checks, circulation verification, vacuum measurement, timer records, cleaning method and contamination control. Maintenance access is essential for repeatable long-term operation.
Request an IEC 60529 Review →Send the standard and IP level, enclosure category, specimen dimensions, dust specification, vacuum requirement, powered state and acceptance criteria.
Request a Dust Test Chamber Proposal Download Dust Chamber InformationDust chamber selection
Start with the required test method and specimen—not the word “sand” in a product name. The three equipment pages below serve different purchasing decisions: an IP dust-ingress configuration, a published 1,000 L cabinet, and a custom chamber for automotive assemblies.
| Your test requirement | Start with this equipment page | Confirm before quotation |
|---|---|---|
| IEC 60529 IP5X or IP6X enclosure dust ingress | ห้องทดสอบฝุ่นละออง Method-led configuration |
The IP designation, enclosure category, specified test dust, pressure-reduction condition, specimen state and inspection criteria. IP5X and IP6X do not have identical acceptance rules. |
| A defined 1,000 L dust-circulation workspace | DR-H508-2 1000 L Sand Dust Test Chamber Published cabinet configuration |
That the loaded specimen fits the 1000 × 1000 × 1000 mm workspace, plus the selected dust medium, test sequence, electrical supply and whether a vacuum pump is included. The cabinet name does not establish a blowing-sand profile. |
| Automotive parts needing a custom fixture or interface | DR-H508 Custom Automotive Sand Test Chamber Project-specific design |
Part drawing, installed orientation, fixture, powered load, cables, pressure connection and the exact test procedure. Airflow and particle-feed capability must be demonstrated if the requirement is blowing sand or blowing dust. |
A short, complete requirement lets the chamber, dust circuit, specimen connection and acceptance test be reviewed together.
Need the method background first? Read the IP5X/IP6X dust-testing guide. Ready to specify equipment? Send your test requirement to DERUI →
อุปกรณ์ทดสอบเดรูอิทมุ่งมั่นให้บริการโซลูชันทดสอบที่แม่นยำและเชื่อถือได้สำหรับการอัปเกรดอุตสาหกรรมทั่วโลก，มีส่วนร่วมในการออกแบบและผลิตอุปกรณ์ทดสอบคุณภาพสูง เช่น อุปกรณ์ทดสอบกระดาษและบรรจุภัณฑ์ ผลิตภัณฑ์หลักของเราได้แก่ ห้องทดสอบสิ่งแวดล้อม และ ห้องทดสอบสภาพอากาศ
