Walk-In Salt Spray Test Room
When a coating panel, fabricated assembly or full-size component will not fit a conventional salt spray cabinet, a walk-in test room provides the access and loading space needed to position the specimen without crowding the fog collectors or nozzle zone.
DERUI configures the room envelope, access door, racks, fog-generation system and site utilities around the largest test article and the selected corrosion method.
What a Larger Test Space Solves
Oversize components
Plan clearance for body panels, enclosures, frames or long coated parts that cannot be mounted correctly in a bench cabinet.
Unobstructed fog exposure
Keep specimens clear of walls, nozzles and each other so runoff and spray shadowing do not distort results.
Repeatable batch loading
Design racks or a loading fixture around the actual part geometry, collection points and operator access.
Size the usable workspace, not just the nominal liters. Provide the largest specimen drawing, loaded orientation, quantity, fixture and door-clearance requirements.
Specify the Room Around the Test Article
| Design item | Information needed | What the approved drawing should show |
|---|---|---|
| Internal room envelope | Largest specimen and loaded fixture dimensions | Usable length, width, clear height and service clearances |
| Access | Operator and trolley movement; part handling method | Door clear opening, threshold, aisle and escape arrangement |
| Fog collection | Selected method and usable test zone | Collector locations and acceptance measurement plan |
| Температура | Required setpoint, tolerance and loaded condition | Sensor layout and temperature-verification points |
| Solution system | Test duration and refill interval | Tank capacity, low-level protection and pipe materials |
| Коммунальные услуги | Site power, air, water, exhaust and drain | Connection schedule, installed load and service access |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | Test modes, data and alarms | Controller functions, records and safety interlocks |
Large Salt Spray Chamber Photo
Method First: NSS, AASS and CASS Are Not the Same
ASTM B117 describes operation of a continuous salt-fog environment; ISO 9227 covers NSS, AASS and CASS apparatus and procedures. The product or customer specification determines the exposure duration and pass/fail criteria. Confirm the adopted edition and method before selecting wetted materials and solution plumbing.
| Method | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | Equipment implication |
|---|---|---|
| NSS | Neutral salt spray for metals and protected/coated surfaces | Control the specified solution, chamber conditions and collected fog. |
| AASS | Acetic-acid salt spray for selected decorative coatings | Check acid compatibility, pH control and cleaning procedure. |
| CASS | Copper-accelerated acid salt spray for selected plated finishes | Check higher-temperature capability, copper-bearing solution handling and contamination control. |
| Cyclic corrosion | Alternating wet, fog and/or dry stages under a separate method | Requires a verified cyclic system; a controller program alone does not establish capability. |
For smaller continuous-fog specimens, review the standard salt spray corrosion chamber. For programmable wet/dry methods, evaluate a dedicated cyclic salt spray chamber.
Five Design Decisions That Control Test Quality
Loading envelope
Define the largest part, handling method, fixture weight and clearance from walls and collectors.
Fog distribution
Specify collector positions across the usable space and acceptance limits under representative loading.
Solution handling
Match tank capacity, refill logic, water quality, pH checks and wetted materials to the test duration.
Room utilities
Plan power, compressed air, exhaust, drainage, floor loading and a route for bringing the specimen into the test area.
Records
Define which temperatures and alarms are logged automatically and which fog/pH readings remain operator measurements.
Maintenance access
Leave safe access to nozzles, collectors, saturator, seals, tank and drain for cleaning and calibration.
Acceptance Test: Prove Performance Across the Usable Space
Before shipment, align the factory acceptance test with the specimen drawing and the agreed method. A practical FAT should cover:
| Проверить | Evidence to keep |
|---|---|
| Dimensional fit | As-built internal and door measurements; rack and specimen loading drawing |
| Контроль температуры | Recorded sensor positions, setpoint, stabilization and deviation |
| Fog collection | Collector layout and measured deposition at defined positions |
| Solution/air system | Tank level protection, air regulation, nozzle operation and refill sequence |
| Safety and records | Low-water/over-temperature responses, alarms and required report export |
A chamber's volume or number of atomizers does not establish uniform exposure. Use the witnessed collection results for the approved loading zone.
Installation and Operating Scope
A walk-in corrosion room needs more than floor area. Before order, confirm floor load, personnel and trolley access, electrical supply, clean compressed air, make-up water, exhaust discharge and corrosion-resistant drainage. Keep salt-laden exhaust away from building HVAC and sensitive equipment; handle acidic or copper-containing waste according to the selected method and local site rules.
The approved room drawing should show clear internal height, door opening, operator route, emergency access, loading fixtures and safe maintenance access.
Часто задаваемые вопросы
How do I size a walk-in salt spray test room?
Start with the largest loaded specimen, trolley or fixture, operator access and required fog-collector clearance. Room volume alone does not establish usable capacity.
Can the room test a 2 m part?
Fit depends on the door opening, orientation, rack, collector positions and required clearances. Send a drawing of the complete loaded part.
Does ASTM B117 set the product's pass/fail hours?
No. ASTM B117 addresses the salt-fog apparatus and operating conditions. The product or customer specification defines exposure time and acceptance criteria.
Can the room run CASS or cyclic corrosion?
Only if the ordered materials, temperature, solution system and controls are engineered and verified for the exact procedure. Continuous NSS capability alone does not establish either mode.
What should be included in the RFQ?
Send the test method and edition, specimen drawing, quantity, fixture, exposure profile, site utilities, data requirements and acceptance points.
Size the Room Around Your Largest Test Article
Share the specimen drawing, selected method, loading arrangement and site utilities. DERUI can prepare a walk-in room configuration and measurable FAT scope.
